Hyundai Equus Manuals

Hyundai Azera: Front Wiper Motor Repair procedures - Windshield Wiper/Washer - Body Electrical System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Front Wiper Motor Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Removal
1.
Loosen the windshield wiper arm nut (B) after removing a wiper cap (A).

2.
Remove the windshield wiper arm and blade.
3.
If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm.

4.
Disconnect the washer hose (A) connected to cowl top cover.

5.
Remove the weather strip and the cowl top cover (A) after removing rivets.

6.
Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

7.
Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts.

8.
Hold the wiper motor crank arm and remove the upper linkage (A).

   
Before removing the wiper motor and linkage assembly, make sure that the linkage is stopped at auto stop position.
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
9.
Remove the lower linkage (A) from the wiper motor crank arm.

   
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
10.
Remove the crank arm (A) after loosening a nut.

11.
Remove the wiper motor (A) after loosening the bolts.

Installation
1.
Install the wiper motor.
2.
Install the crank arm.
Torque :
12.7~17.6 Nm (1.3~1.8 kgf.m, 9.4~13.0 lbf.ft)
   
To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.
3.
Install the lower and upper linkage to the wiper motor crank arm.
4.
Install the wiper motor and linkage assembly and then connect the wiper motor connector.
Torque :
7~11 Nm (0.7~1.1 kgf.m, 5.0~7.9 lbf.ft)
5.
Install the cowl top cover.
6.
Install the windshield wiper arm and blade.
Torque :
23 ~ 27 Nm (2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lbf.ft)
   
-
The windshield wiper motor must be cycled to make sure that it is in the auto stop position.
If necessary, adjust the wiper arm and blade.
7.
Install the wiper arm and blade to the specified position.
A : Auto stop position (Blade)

8.
Set the cowl top cover on the specified spray position.
   
-
When you turn on the washer, confirm 50% or more of washer fluid lands within the spray area.
-
If the spray area is not within the standard positions, adjust the nozzle(s).

Specified position
Distance (in)
Distance (mm)
A
33.27
845
B
31.85
808.9
C
20.67
525.1
D
17.43
442.8
E
11.16
283.4
F
10.31
261.8
G
8.89
225.9
H
7.85
199.4
I
3.68
93.5
J
22.68
576
K
24.76
629
L
1.66
42.1
M
2.81
71.5

Inspection
Speed Operation Check
1.
Remove the connector (A) from the wiper motor.

No.
Description
No.
Description
1
-
4
High
2
Battery (+)
5
GND
3
Gear P
6
Low

2.
Attach the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 5.
3.
Check that the motor operates at low or high speed as below table.

   
Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.
Front Wiper Motor Components and Components Location
Component Location 1. Cap2. Nut3. Wiper arm & blade4. Rivet5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly ...

Front Washer Motor Repair procedures
Inspection 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water.     Before filling the reservoir tank with water, check the filter for ...

See also:

Relay Box (Engine Compartment) Repair procedures
Inspection Power Relay Test (Type A)     - Do not use pliers. - Pliers will damage the relays, which could cause the engine to stall or not start. - Carefully remove ...

Air Ventilation Seat Repair procedures
Removal [Front Seat] 1. Remove the front seat assembly. (Refer to Body - "Front Seat Assembly") 2. Remove the seat back cover and cushion cover. (Refer to Body - "Front Seat Cushion Cover") ...

Power Window Motor Repair procedures
Inspection Front Power Window Motor Inspection 1. Remove the front door trim panel. (Refer to Body - "Front Door Trim") 2. Disconnect the connector from the motor. 3. Connect the termina ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com