Hyundai Equus Manuals

Hyundai Azera: Front Hub - Axle Repair procedures - Front Axle Assembly - Driveshaft and axle - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Front Hub - Axle Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub - Axle Repair procedures

Replacement
1.
Loosen the wheel lug nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire(A) from front hub.
Tightening torque:
88.2 ~ 107.8N.m(9.0 ~ 11.0kgf.m, 65.0 ~ 79.5lb-ft)

   
Be careful not to damage to the hub bolts when removing the front wheel and tire(A).
3.
Loosen the wheel speed sensor mount bolt and then remove the wheel speed sensor(A) from the knuckle.
Tightening torque:
6.8 ~ 10.7N.m(0.7 ~ 1.1kgf.m, 5.0 ~ 7.9lb-ft)

4.
Remove the brake caliper mounting bolts , and then place the brake caliper assembly(A) with wire.
Tightening torque:
78.4 ~ 98.0N.m(8.0 ~ 10.0kgf.m, 57.8 ~ 72.3lb-ft)

5.
Remove the tie rod end ball joint(A) from the knuckle.
(1)
Remove the split pin(B).
(2)
Remove the castle nut(C).
Tightening torque:
34.3 ~ 44.1N.m(3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)

6.
Remove driveshaft coking nut(A) from the front hub under applying the brake.
Tightening torque:
274.6 ~ 294.2 N.m (28.0 ~ 30.0 kgf.m, 202.5 ~ 217.0 lb-ft)

   
•
The rear hub lock nut should be replaced with new ones.
•
After installation lock nut, stake the lock nut using a chisel and hammer as shown in the illustration below.

7.
Remove the lower arm(A) from the knuckle.
Tightening torque:
98.0 ~ 117.6N.m(10.0 ~ 12.0kgf.m, 72.3 ~ 86.7lb-ft)

8.
Disconnect the driveshaft(A) from the front hub assembly.
Tightening torque:
137.2 ~ 156.9N.m(14.0 ~ 16.0kgf.m, 101.2 ~ 115.7lb-ft)

   
Be careful not to damage the boot and tone wheel.
9.
Loosen the strut bolts and nuts and then remove the kunckle assembly(A).
Tightening torque:
156.9 ~ 176.5 N.m (16.0 ~ 18.0 kgf.m, 115.7 ~ 130.2 lb-ft)

Disassembly
1.
Remove the snap ring(A).

2.
Remove the hub assembly from the knuckle assembly.
(1)
Install the front knuckle assembly(A) on press.
(2)
Lay a suitable adapter(B) upon the hub assembly shaft.

3.
Remove the hub bearing inner race from the hub assembly.
(1)
Install a suitable tool(A) for removing the hub bearing inner race on the hub assembly.
(2)
Lay the hub assembly and tool(A) upon a suitable adapter(B).
(3)
Lay a suitable adapter(C) upon the hub assembly shaft.
(4)
Remove the hub bearing inner race(D) from the hub assembly by using press.

4.
Remove the hub bearing outer race from the knuckle assembly.
(1)
Lay the hub assembly(A) upon a suitable adapter(B).
(2)
Lay a suitable adapter(C) upon the hub bearing outer race.
(3)
Remove the hub bearing outer race from the knuckle assembly by using press.

5.
Replace hub bearing with a new one.
Reassembly
1.
Install the hub bearing to the knuckle assembly.
(1)
Lay the knuckle assembly(A) on press.
(2)
Lay a new hub bearing upon the knuckle assembly(A).
(3)
Lay a suitable adapter(B) upon the hub bearing.
(4)
Install the hub bearing to the knuckle assembly by using press.

   
•
Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.
•
Always use a new wheel bearing assembly.
2.
Install the hub assembly to the knuckle assembly.
(1)
Lay the hub assembly(A) upon a suitable adapter.
(2)
Lay the knuckle assembly(B) upon the hub assembly(A).
(3)
Lay a suitable adapter upon the hub bearing.
(4)
Install the hub assembly(A) to the knuckle assembly(B) by using press.

   
Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.
3.
Install the snap ring(A).

Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the knuckle for cracks.
4.
Check the bearing for cracks or damage.
Installation
1.
Install in the reverse order of removal.
   
•
Use a SST (09581-11000) when installing the brake caliper assembly.
Front Hub - Axle Components and Components Location
Components 1. Coking nut2. Brake disc3. Hub4. Dust cover5. Knuckle6. Wheel bearing7. Snap ring8. Drive shaft ...

Driveshaft Assembly
...

See also:

Fuel Line Repair procedures
Removal     In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure f ...

Cluster ionizer Repair procedures
Inspection 1. Press the OFF switch more then 4 times within 2 seconds while pressing the MODE switch. DisplayFail description00Normal50Cluster ionizer fault * Diagnostic procedure refer to D ...

Digital clock (if equipped)
WARNING Do not adjust the clock while driving. You may lose your steering control and cause an accident that results in severe personal injury or death. Whenever the battery terminals or relate ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com