Hyundai Equus Manuals

Hyundai Azera: Tire Repair procedures - Tires/Wheels - Suspension System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Tire Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Suspension System / Tires/Wheels / Tire Repair procedures

   
•
Using tires and wheel other than the recommended sizes could cause unusual handling characteristics and poor vehicle control, resulting in a serious accident.
Tire Wear
1.
Measure the tread depth of the tires.
Tread depth [limit] : 1.6 mm (0.0630 in.)
2.
If the remaining tread depth (A) is less than the limit, replace the tire.
   
When the tread depth of the tires is less than 1.6 mm(0.063 in), the wear indicators (B) will appear.

Tire Rotation
Checking For Pull And Wander
If the steering pulls to one side, rotate the tires according to the following wheel rotation procedure.
1.
Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.

2.
If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.

3.
If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.

4.
If the steering continues to pull to the opposite side, replace the front wheels with new ones.

Removal
1.
Remove valve core and deflate the tire.
2.
Remove the side of the tire bead area from the wheel using tire changing machine .

   
•
The tire bead should be broken approx. 90° from the valve side of the wheel. The bead breaker should not be set too deep.
•
Avoid tire/tool contact with the valve on dismount.
•
Dismount should end near the valve.
3.
Rotate the wheel clockwise.

Installation
1.
Apply tire soap or lubrication to the top and bottom tire beads.

2.
To fit the bottom bead, position the valve at the 5 o’clock position relative to the head on the tire changing machine.

3.
Place the tire on the rim so the bottom bead touches the edge of the rim after the valve (6 o’clock). Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to fit bottom bead.

4.
After bottom bead is on tire, rotate the rim until the valve is at the 5 o’clock position relative to the head on the tire changing machine. Push down on the tire at the 3 o’clock position and rotate the rim clockwise to fit the top bead.

5.
Inflate the tire until both beads seat.
Tire presuure : 2.2kg/cm? (32psi)

Tires/Wheels
...

Wheel Repair procedures
Lug nut tightening sequence Tighten the hub nuts as follows. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     When using an impact gun, final tigh ...

See also:

Fuel Tank Repair procedures
Removal 1. Release the residual pressure in fuel line. (Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”) 2. Remove the fuel pump service cover (A) in the trunk. ...

Front Door Inside Handle Repair procedures
Replacement 1. Remove the front door trim. (Refer to Front Door - "Front Door Trim") 2. After loosening the mounting screws, then remove the front door inside handle (A). 3. Installation ...

Input Speed Sensor Description and Operation
Description Input speed sensor is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the Transaxle Control Module(TCM). The sen ...

Categories

Hyundai Azera Manuals

2011-2026 Copyright www.hgmanual.com