Hyundai Equus Manuals

Hyundai Azera: Brake Booster Repair procedures - Brake System - Brake System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Brake Booster Repair procedures

Brake Booster Operating Test
For simple checking of the brake booster operation, carry out the following tests.
1.
Run the engine for one or two minutes, and then stop it. If the pedal depresses fully the first time but gradually becomes higher when depressed succeeding times, the booster is operating properly, if the pedal height remains unchanged, the booster is inoperative.

2.
With the engine stopped, step on the brake pedal several times.
Then step on the brake pedal and start the engine. If the pedal moves downward slightly, the booster is in good condition. If there is no change, the booster is inoperative.

3.
With the engine running, step on the brake pedal and then stop the engine.Hold the pedal depressed for 30 seconds. If the pedal height does not change, the booster is in good condition, if the pedal rises, the booster is inoperative.
If the above three tests are okay, the booster performance can be determined as good.
Even if one of the above three tests is not okay, check the check valve, vacuum hose and booster for malfunction.

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air duct (B) and air cleaner assembly (A).

3.
Remove the battery and battery tray.
4.
Disconnect a connector and loosen the wiring harness mounting nuts. Then pivot the wiring harness (A) side out of the way.

5.
Disconnect the brake fluid level switch connector (B), and remove the reservoir cap.

6.
Remove the brake fluid from the master cylinder reservoir with a syringe.
   
Do not spill brake fluid on the vehicle, it may damage the paint ; if brake fluid does contact the paint, wash if off immediately with water.
7.
Remove the brake tube (A).

Tightening torque:
18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)

8.
Remove the master cylinder (B) from the brake booster after loosening the mounting nuts (A).

Tightening torque:
12.7 ~ 16.7 N.m (1.3 ~ 1.7 kgf.m, 9.4 ~ 12.3 lb-ft)

9.
Disconnect the vacuum hose (A) from the brake booster.

10.
Remove the snap pin (A) and clevis pin (B).

11.
Remove the mounting nuts.

Tightening torque:
12.7 ~ 15.7 N.m (1.3 ~ 1.6 kgf.m, 9.4 ~ 11.6 lb-ft)

12.
Remove the brake booster (A).

Inspection
1.
Inspect the check valve in the vacuum hose.
   
Do not remove the check valve from the vacuum hose.
2.
Check the boot for damage.
Installation
1.
Installation is the reverse of removal.
   
A.
Before installing the pin, apply the grease to the joint pin.
B.
Use a new snap pin whenever installing.
2.
After installing, bleed the brake system.
(Refer to Brake system bleeding)
3.
Adjust the brake pedal height and free play.
(Refer to Brake pedal height and free play adjustment)
Brake Booster Components and Components Location
Components 1. Brake booster2. Master cylinder assembly3. O-ring ...

Master Cylinder Components and Components Location
Components 1. Reservoir cap2. Reservoir3. Grommet4. Master cylinder ...

See also:

Idler Components and Components Location
Components 1. Idler ...

Components and Components Location
Components 1. Sub frame2. Coil spring3. Upper arm4. Assist arm5. Trailing arm6. Rear axle ...

Rear Lower Arm Repair procedures
Removal 1. Remove the rear wheel & tire (A). Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     • Be careful not to damage to the hub bolts ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com