Specification |
Engine & T/M | Joint type | Max. permissible angle | ||
Inner | Outer | Outer | Inner | |
RAMDA 3.0 MPI A/T | BJ#104 | PTJ#100 | 45° | 21° |
RAMDA 3.3 GDI A/T | BJ#104 | PTJ#100 | 45° | 21° |
Tightening Torque |
Item | N.m | kgf.m | Ib-ft | |
Front | Wheel lug nuts | 88.2 ~ 107.8 | 9.0 ~ 11.0 | 65.0 ~ 79.5 |
Drive shaft coking nut | 274.6 ~ 274.5 | 28.0 ~ 30.0 | 202.5 ~ 217.0 | |
Strut assembly lower mounting bolt | 156.9 ~ 176.5 | 16.0 ~ 18.0 | 115.7 ~ 130.2 | |
Brake caliper mounting bolt | 78.4 ~ 98.0 | 8.0 ~ 10.0 | 57.8 ~ 72.3 | |
Wheel speed sensor mounting bolt | 6.8 ~ 10.7 | 0.7 ~ 1.1 | 5.0 ~ 7.9 | |
Brake disc mounting bolt | 4.9 ~ 5.8 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
Lower ball joint mounting bolt | 98.0 ~ 117.6 | 10.0 ~ 12.0 | 72.3 ~ 86.7 | |
Tie rod end ball joint nut | 34.3 ~ 44.0 | 3.5 ~ 4.5 | 25.3 ~ 32.5 | |
Rear | Wheel nut | 88.2 ~ 107.8 | 9.0 ~ 11.0 | 65.0 ~ 79.5 |
Shock absorber upper mounting bolt | 137.2 ~ 156.9 | 14.0 ~ 16.0 | 101.2 ~ 115.7 | |
Shock absorber lower mounting nut | 137.2 ~ 156.9 | 14.0 ~ 16.0 | 101.2 ~ 115.7 | |
Brake caliper mounting bolt | 78.4 ~ 98.0 | 8.0 ~ 10.0 | 57.8 ~ 72.3 | |
Wheel speed sensor mounting bolt | 6.8 ~ 10.7 | 0.7 ~ 1.1 | 5.0 ~ 7.9 | |
Brake disc mounting bolt | 4.9 ~ 5.8 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
Hub assembly mounting bolt | 78.4 ~ 88.2 | 8.0 ~ 9.0 | 57.8 ~ 65.0 | |
Upper arm ball joint mounting nut | 137.2 ~ 156.9 | 14.0 ~ 16.0 | 101.2 ~ 115.7 | |
Lower arm mounting bolt | 137.2 ~ 156.9 | 14.0 ~ 16.0 | 101.2 ~ 115.7 | |
Assist arm ball joint mounting nut | 78.5 ~ 88.3 | 8.0 ~ 9.0 | 57.9 ~ 65.1 | |
Trailing arm mounting bolt | 44.1 ~ 53.9 | 4.5 ~ 5.5 | 32.5 ~ 39.7 |
Lubricants |
Engine & T/M | Joint type | Lubricants | Quantity |
RAMDA 3.0 MPI A/T | BJ#104 | GRB006 | 145g(+10g) |
PTJ#100 | SH06-VX21 | 220g(±10g) | |
RAMDA 3.3 GDI A/T | BJ#104 | GRB006 | 145g(+10g) |
PTJ#100 | SH06-VX21 | 220g(±10g) |
Closing the fuel filler lid
1. To install the cap, turn it clockwise until it clicks one time. This indicates
that the cap is securely tightened.
2. Close the fuel filler lid and push it lightly and make sure that it is secure ...
Alignment Repair procedures
Front Wheel Alignment
When using a commercially available computerized wheel
alignment equipment to inspect the front wheel alignment, always
position the vehicle on a lev ...
CVVT Oil Control Valve (OCV) Specifications
Specification
ItemSpecificationCoil Resistance (?)9.4 ~ 10.4 [20°C(68°F)]
...