Hyundai Equus Manuals

Hyundai Azera: Brake Pedal Repair procedures - Brake System - Brake System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Brake Pedal Repair procedures

Fifth generation HG (2011–2024) / Hyundai Azera 2011-2024 Service Manual / Brake System / Brake System / Brake Pedal Repair procedures

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the crash pad lower panel.
3.
Remove the shower duct (A).

4.
Disconnect the stop lamp switch connector (A).

5.
Remove the brake pedal member mounting nut (B).

6.
Remove the snap pin (A) and clevis pin (B).

7.
Remove the brake pedal member assembly mounting nuts (A) and then remove the brake pedal assembly.

Inspection
1.
Check the bushing for wear.
2.
Check the brake pedal for bending or twisting.
3.
Check the brake pedal return spring for damage.
4.
Check the stop lamp switch.
(1)
Connect a circuit tester to the connector of stop lamp switch, and check whether or not there is continuity when the plunger of the stop lamp switch is pushed in and when it is released.
(2)
The stop lamp switch is in good condition if there is no continuity when plunger(A) is pushed.

Installation
1.
Pre-tighten the bracket fixing bolt (A) in dash panel.

2.
Install the brake booster and brake pedal member fixing nuts (A) securely.
Tightening torque:
12.7 ~ 15.7 N.m (1.3 ~ 1.6 kgf.m, 9.4 ~ 11.6 lb-ft)

3.
Tighten the bolt (A) securely in dash panel.
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

4.
Install the snap pin (A) and clevis pin (B).

   
•
Before installing the pin, apply the grease to the clevis pin.
•
Use a new snap pin whenever installing.
5.
Install the stop lamp switch securely.
6.
Connect the stop lamp switch connector (A).

7.
Adjust the brake pedal height and free play.
8.
Check the brake pedal operation after installing the brake pedal.
9.
Install the shower duct (A).

10.
Install the crash pad lower panel.
11.
Reconnect the battery negative cable.
Adjustment
Stop lamp switch clearance adjustment
If the gap between stop lamp switch and bracket is not 1.0 ~ 2.0mm(0.04~ 0.08in), conform to below.
1.
Disconnect the stop lamp switch connector (A).

2.
Pull the locking plate (A) as indicated by the arrow.

3.
Turn stop lamp switch 45° counterclockwise and remove it.

4.
Fix the brake pedal arm and insert fully the stop lamp switch as hiding contact part.

5.
After inserting, turn the stop switch (A) 45° clockwise, and then assemble locking plate (B) by pushing.

6.
Confirm the gap between stop lamp switch and bracket.
Stop lamp clearance:
1.0 ~ 2.0 mm (0.04 ~ 0.08 in)

7.
Connect the stop lamp switch connector.
Brake Pedal Components and Components Location
Components 1. Cowl bracket2. Brake pedal member assembly3. Stop lamp switch4. Return spring5. Brake pedal stopper6. Clevis pin7. Snap pin8. Brake pedal ...

Front Disc Brake Components and Components Location
Components 1. Guide rod bolt2. Bleed screw3. Caliper carrier4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer ...

See also:

Components and Components Location
Component Location 1. Rear glass defogger relay (Engine room relay box)2. Rear glass defogger switch (A/C controller)3. Rear glass defogger ...

Automatic climate control system (Type  A)
1. Front windshield defroster button 2. Fan speed control knob 3. OFF button 4. Rear window defroster button 5. Dual temperature control selection button 6. Mode selection button 7. Passenge ...

Overdrive Clutch Control Solenoid Valve(OD/C_VFS) Description and Operation
Description Overdrive clutch control solenoid valve(OD/C) is attached to the valve body. This variable force solenoid valve directly controls the hydraulic pressure inside the overdrive clutch. ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com