Hyundai Equus Manuals

Hyundai Azera: Parking Brake Pedal Assembly Repair procedures - Parking Brake System - Brake System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Parking Brake Pedal Assembly Repair procedures

Fifth generation HG (2011–2024) / Hyundai Azera 2011-2024 Service Manual / Brake System / Parking Brake System / Parking Brake Pedal Assembly Repair procedures

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the crash pad lower panel.
3.
Remove the junction box.
4.
Disconnect the parking brake switch connector (A).

5.
Remove the parking brake cable mounting nuts (A).

6.
Remove the parking brake pedal mounting bolts (A) and nut (B).

7.
Remove the parking brake cable adjusting nut(A) and the fixing clip(B), and then remove the parking brake pedal.

Installation
1.
Install the holding clip (B) and the cable adjusting nut(A) after fixing the parking brake cable.

2.
Install the parking brake pedal, and then install the parking brake pedal mounting bolts (A) and nuts (B).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

3.
Adjust the parking brake pedal stroke by turning the adjusting nut (A).
(1)
Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables.

(2)
Adjust the adjusting nut (A) for parking brake pedal stroke 3 ~ 4 notches when operating effort is 196N(20kgf.44lb).
   
1.
The parking brake adjustment must be carried out after adjusting the rear shoe.
2.
After adjusting parking brake, notice following matter.
1)
Must be free from clearance between adjusting nut and pin.
2)
Check securely that the brake is not dragging.
4.
Reconnect the parking brake switch connector (A).

5.
Install the juncting box.
6.
Install the crash pad lower panel.
Adjustment
Parking Brake Pedal Stroke Adjustment
1.
Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables.
2.
Adjust the adjusting nut(A) for parking barke pedal stoke 4~5 notches when operating effort is 196N(20kgf, 44lbf)

   
1.
The parking brake adjustment must be carried out after adjusting the rear shoe.
2.
After adjusting parking brake, notice following matter.
1)
Must be free from clearance between adjusting nut and pin.
2)
Check securely that the brake is not dragging.
Parking Brake Assembly Repair procedures
Removal Parking Brake Shoe 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. (Refer ...

Parking Brake Cable Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. (Refer to Body - "Crash pad lower panel") 3. Remove the parking bra ...

See also:

Shift Cable Repair procedures
Removal 1. Remove the center console assembly. (Refer to Body - "Console") 2. Remove the duct (A). 3. Remove the control cable (B). 4. Remove the control cable assembly in the vehicle ...

Transaxle Control Module (TCM) Schematic Diagrams
TCM connector and terminal function TCM Terminal Function Connector [ELG-A] PinDescriptionPinDescription1?51?2?52?3?53?4?54Sports mode down switch5?55?6?56?7?57?8?58?9CCP CAN(HIGH)59?10CAN Commu ...

Repair procedures
Adjustment Inspect Glass Alignment 1. Check for abnormal noise or bending during operation. 2. With the sunroof fully closed, check for water leakage. 3. The roof panel (B) should be even ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com