Circuit Diagram - ESC (1) |
Circuit Diagram - ESC (2) |
Circuit Diagram - ESC (3) |
Circuit Diagram - ESC (4) |
ESC connector input/output |
Connector Terminal | Specification | |
Pin No | Description | |
29 | IGNITION1(+) | High level of wake up voltage : 4.5V < V < 16.0V Low level of wake up voltage : V < 2.4V Max. current : I < 50mA |
25 | POS. BATTERY 1.(SOLENOID) | Over voltage range : 17.0 ± 0.5V Operating voltage range : 10.0 ± 0.5V < V < 16.0 ± 0.5V Low voltage range : 7.0 ± 0.5V < V < 9.5 ± 0.5V Max. current : I < 40A Max. leakage current : I < 0.25mA |
1 | POS. BATTERY 2.(MOTOR) | Operating voltage range: 10.0 ± 0.5V < V < 16.0 ± 0.5V Rush current : I < 110A Max current : I < 40A Max leakage current : I < 0.25mA |
38 | GROUND | Rated current : I <550mA Max. current: I < 40A |
13 | PUMP MOTOR GROUND | Rush current : I < 110A Max current : I < 40A |
11 | SENSOR GROUND | Rated current : I <250mA |
4 | SENSOR POWER | Max current Capability : I < 250mA Max voltage : V_BAT1 -0.8V |
23 | BRAKE LIGHT SWITCH | Input voltage (Low) : V < 2V Input voltage (High) : V > 6V Max. Input current : I < 3mA (@12.8V) |
10 | ESC ON/OFF SWITCH | |
22 | PARKING BRAKE SWITCH | Input voltage (Low) : V < 2V Input voltage (High) : V > 6V Max input current : I < 5mA (@12.8V) |
28 | SENSOR FRONT RIGHT OUTPUT | External pull up resistance : 1 K? < R Output duty :50 ± 20% |
14 | CAN BUS LINE(LOW) | Max. Input current : I < 10mA |
26 | CAN BUS LINE(HIGH) | |
18 | SENSOR FRONT LEFT POWER | Output voltage : V_BAT1 -0.6V ~ V_BAT1 -1.1V Output current : Max 30mA |
34 | SENSOR FRONT RIGHT POWER | |
19 | SENSOR REAR LEFT POWER | |
33 | SENSOR REAR RIGHT POWER | |
31 | SENSOR FRONT LEFT SIGNAL | Input current LOW : 5.9 ~ 8.4mA Input current HIGH : 11.8 ~ 16.8mA Frequency range : 1 ~ 2500Hz Input duty : 50 ± 10% |
21 | SENSOR FRONT RIGHT SIGNAL | |
32 | SENSOR REAR LEFT SIGNAL | |
20 | SENSOR REAR RIGHT SIGNAL | |
12 | CAN SENSOR LINE (HIGH) | Max. input current : I < 10mA |
24 | CAN SENSOR LINE (LOW) | |
8 | HAC RELAY DRIVE | Max. Current : I< 180mA Max.Output Low Voltage : V< 1.2V |
9 | BRAKE SWITCH | Input voltage (Low) : V < 2V Input voltage (High) : V > 6V Max. Input current : I < 10mA |
36 | RELAY STATE MONITORING |
Fender Garnish Repair procedures
Replacement
•
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related parts, to
prevent damage.
•
Put ...
Windshield Deicer Repair procedures
Inspection
1.
Remove the cowl top cover.
(Refer to Windshield Wiper/Washer - "Front Wiper Motor")
2.
Disconnect the windshield deicer connector from the wiper motor linkage.
3.
Check for ...
Closing the sunroof
Press the sunshade CLOSE button. The sunroof glass will close then the sunshade
will close. To stop the sunroof movement at any point, press the sunshade control
switch momentarily.
If you want ...