Hyundai Equus Manuals

Hyundai Azera: Sub Frame Repair procedures - Front Suspension System - Suspension System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Sub Frame Repair procedures

Fifth generation HG (2011–2024) / Hyundai Azera 2011-2024 Service Manual / Suspension System / Front Suspension System / Sub Frame Repair procedures

Replacement
1.
Remove the front wheel & tire (A).
Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

   
•
Be careful not to damage to the hub bolts when removing the front wheel & tire.
2.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening torque :
32.4 ~ 34.3N.m (3.3 ~ 3.5kgf.m, 23.9 ~ 25.3lb-ft)

   
•
Keep the neutral-range to prevent the damage of the clock spring inner cable when you handle the steering wheel.
•
Make sure when you reassemble the universal joint and pinion shaft certainly has been inserted.
3.
Remove the under cover (A).

4.
Remove the sprit pin and castle nut and then disconnect the tie-rod end (A) from the front knuckle.
Tightening torque :
34.3~44.1N.m(3.5~4.5Kgf.m, 25.3~32.5lb-ft)

5.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque :
98.1~117.7N.m(10.0~12.0Kgf.m, 72.3~86.8lb-ft)

6.
Disconnect the stabilizer link (B) with the front strut assembly (A) after loosening the nut.
Tightening torque :
98.1~117.7N.m(10.0~12.0Kgf.m, 72.3~86.8lb-ft)

7.
Loosen the bolt and then remove the front roll stopper (A).
Tightening torque :
107.9~117.7N.m(11.0~13.0Kgf.m, 79.6~94.0lb-ft)

8.
Disconnect the muffler rubber hanger (A).

9.
Loosen the bolts & nuts and then remove the sub frame (A).
Tightening torque :
Sub frame mounting bolts & nuts :
156.9 ~ 176.5N.m (16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)
Sub frame bracket bolts & nuts :
44.1 ~ 58.8N.m (4.5 ~ 6.0kgf.m, 32.5 ~ 43.4lb-ft)

10.
Remove the front lower arm.
(Refer to Front Suspension System - "Front Lower Arm")
11.
Remove the front strut assembly.
(Refer to Front Suspension System - "Front Strut Assembly")
12.
Remove the front stabilizer bar.
(Refer to Front Suspension System - "Front Stabilizer Bar")
13.
Remove the steering gear box.
14.
Installation is the reverse of removal.
15.
Check the alignment.
(Refer to Tires/Wheels - "Alingnent")
Front Stabilizer Bar Repair procedures
Replacement 1. Remove the front wheel & tire (A). Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     • Be careful not to damage to the hub b ...

Rear Suspension System
...

See also:

Specifications
Specifications ItemsSpecificationHoodTypeRear hinged, gas lifter typeFront DoorConstructionFront hinged, full door constructionRegulator systemWire drum typeLocking systemPin-fork systemRear Door ...

Schematic Diagrams
Schematic Diagram Canister Canister is filled with charcoal and absorbs evaporated vapor in fuel tank. The gathered fuel vapor in canister is drawn into the intake manifold by the ECM/PCM when ...

Rear Back Armrest Cup Holder Repair procedures
Replacement     • Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. • Take care not to bend or scratch the trim and pan ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com