Hyundai Azera: Description and Operation
Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Restraint / General Information / Description and Operation
Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Restraint / General Information / Description and Operation
| Warning Lamp Activation |
| Warning Lamp Behavior after Ignition On |
As soon as the operating voltage is applied to the SRSCM
ignition input, the SRSCM activates the warning lamp for a LED lamp
check.
The lamp shall turn on for 6 seconds during the initialization phase and be turned off afterward.
To alert the driver, the warning lamp shall turn on for 6
seconds and off for one second then on continuously after the operating
voltage is applied if any active fault exists.
| 1. |
Active fault or historical fault counter is greater or equal to 10.
|
| 2. |
Normal or historical fault counter is less than 10.
|
| 3. |
When turning the ignition switch ON during variant coding
(EOL) mode, the airbag warning lamp illuminates and blinks at intervals
of 1 second till the coding is completed.
In case the variant coding is completed normally, the airbag
warning lamp is turned on for 6 seconds, and then turned off. Otherwise
the airbag warning lamp continuously blinks at intervals of 1 second.
When there is active fault in airbag system or SRSCM internal
fault, the variant coding (EOL) can’t be completed. In this case, do
the variant coding (EOL) procedure again after troubleshooting with the
GDS.
|
SRSCM Independent Warning Lamp Activation
There are certain fault conditions in which the SRSCM cannot
function and thus cannot control the operation of the standard warning
lamp. In these cases, the standard warning lamp is directly activated by
appropriate circuitry that operates independently of the SRSCM. These
cases are:
| 1. |
Loss of battery supply to the SRSCM : warning lamp turned on continuously. |
| 2. |
Loss of internal operating voltage : warning lamp turned on continuously. |
| 3. |
Loss of Microprocessor operation : warning lamp turned on continuously. |
| 4. |
SRSCM not connected : warning lamp turned on continuously. |
Telltale Lamp Activation
The Telltale Lamp indicates the Passenger Airbag(PAB) enabled
and disabled status based on occupant status of passenger seat. If the
passenger seat is empty or occupied with a child (or child seat), the
Passenger Airbag is disabled and the Telltale Lamp is turned ON to
inform the driver that the PAB is disabled. As soon as operating voltage
is applied to the SRSCM ignition input, the SRSCM activates telltale
lamp prove out. ODS (Occupant Detection System) will send an
indeterminate status to the SRSCM as a default setting for passenger
airbag deployment during the prove out period.
After ignition on, telltale lamp will turn on for 4 seconds
and turn off for 3 seconds during the initialization phase and be turned
ON afterward until receipt of valid enabled message from ODS system.
General Safety Information and Caution
Precautions
General Precautions
Please read the following precautions carefully before performing the airbag system service.
Observe the instructions described in this manual, or the airbags c ...
Repair procedures
Component Replacement After Deployment
Before doing any SRS repairs, use the GDS to check for DTCs.
Refer to the Diagnostic Trouble Code list for repairing of the related
...
See also:
Vacuum crankcase ventilation hoses
Inspect the surface of hoses for evidence of heat and/or mechanical damage. Hard
and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate
deterioration. Particular atten ...
Description and Operation
Description
You can up & down rear curtain automatically by pressing
the rear curtain switch. Rear curtain protect passenger from a direct
ray of light by covering rear glass.
...
Crash Pad Lower Panel Components and Components Location
Component Location
1. Crash pad lower panel
...
Categories
Hyundai Azera Manuals
© 2011-2026 Copyright www.hgmanual.com