Hyundai Equus Manuals

Hyundai Azera: Camshaft Repair procedures - Cylinder Head Assembly - Engine Mechanical System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Camshaft Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Engine Mechanical System / Cylinder Head Assembly / Camshaft Repair procedures

Removal
[RH]
1.
Remove the RH bank timing chain.
(Refer to Timing System - "Timing Chain")
2.
Remove the RH exhaust CVVT oil control valve.
3.
Remove the RH camshaft bearing cap (A) and thrust bearing cap (B).

4.
Remove the RH intake camshaft (A) and exhaust camshaft (B)

[LH]
1.
Remove the RH/LH timing chain.
(Refer to Timing System - "Timing Chain")
2.
Remove the LH exhaust CVVT oil control valve.
3.
Remove the fuel pump bracket (A)

4.
Remove the LH camshaft bearing cap (A) and thrust bearing cap (B).

5.
Remove the LH intake camshaft (A) and exhaust camshaft (B)

Installation
   
•
Apply a light coat of engine oil on camshaft journals.
•
Assemble the key groove of camshaft rear side to the same level of head top surface.
•
Be careful the right, left bank, intake, exhaust side before assembling.
[RH]
1.
Install the RH intake camshaft (A) and exhaust camshaft (B)

RH Inkate camshaft

As for camshaft identification, refer to the table below.
Outer diameter
A
30mm (1.1811in.)
B
27mm (1.0630in.)
C
30mm (1.1811in.)
D
30mm (1.1811in.)
E
30mm (1.1811in.)

RH Exhaust camshaft

As for camshaft identification, refer to the table below.
Outer diameter
A
27mm (1.0630in.)
B
27mm (1.0630in.)
C
30mm (1.1811in.)
D
30mm (1.1811in.)

2.
Install the bearing cap (A) and thrust bearing cap (B) with specified torque.
Tightening torque :
1st step : 5.8N.m (0.6kgf.m, 4.3lb-ft)
2nd step : 9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

   
Be sure to install the thrust bearing cap bolts and the bearing cap bolts in the correct place.
   
Be careful the right, left bank, intake, exhaust side before assembling.

A : L(LH),R(RH)
B : I(Intake), None(Exhaust)
C : Journal number
D : Front mark
   
Rotate the crankshaft not to contact the valves to the pistons by making the pistons below 10mm(0.3937in.) from the top of cylinder block.
3.
Install the other parts reverse order of removal.
[LH]
1.
Install the LH intake camshaft (A) and exhaust camshaft (B)

LH Inkate camshaft

As for camshaft identification, refer to the table below.
Outer diameter
A
-
B
-
C
-
D
-
E
-

   
The LH intake camshaft dosen't have identification ring.
LH Exhaust camshaft

As for camshaft identification, refer to the table below.
Outer diameter
A
27mm (1.0630in.)
B
27mm (1.0630in.)
C
30mm (1.1811in.)
D
27mm (1.0630in.)

2.
Install the bearing cap (A) and thrust bearing cap (B) with specified torque.
Tightening torque :
1st step : 5.8N.m (0.6kgf.m, 4.3lb-ft)
2nd step : 9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

   
Be sure to install the thrust bearing cap bolts and the bearing cap bolts in the correct place.
   
Be careful the right, left bank, intake, exhaust side before assembling.

A : L(LH),R(RH)
B : I(Intake), None(Exhaust)
C : Journal number
D : Front mark
   
Rotate the crankshaft not to contact the valves to the pistons by making the pistons below 10mm(0.3937in.) from the top of cylinder block.
3.
Install the fuel pump bracket (A)
Tightening torque :
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)

4.
Install the other parts reverse order of removal.
Camshaft Components and Components Location
Components 1. RH exhaust camshaft2. RH intake camshaft3. LH intake camshaft4. LH exhaust camshaft ...

Cylinder Head Components and Components Location
Components 1. RH Cylinder head2. RH Cylinder head gasket3. LH Cylinder head4. LH Cylinder head gasket5. Cylinder block 1. Camshaft bearing cap 2. Camshaft thrust bearing cap 3. RH Exhaust ca ...

See also:

Passive Occupant Detection System (PODS-F) Repair procedures
Removal PODS-F ECU 1. Disconnect the battery negative cable, and wait for at least three minutes before beginning work. 2. Remove the front passenger seat assembly. (Refer to Body - "Front s ...

Non-operational conditions of rear parking assist system
The rear parking assist system may not operate properly when: 1. Moisture is frozen to the sensor. (It will operate normally when the moisture has been cleared.) 2. The sensor is covered with forei ...

Hazardous driving conditions
When hazardous driving conditions are encountered such as water, snow, ice, mud, sand, or similar hazards, follow these suggestions: Drive cautiously and allow extra distance for braking. Avoid ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com