Hyundai Equus Manuals

Hyundai Azera: Main Crash Pad Assembly Repair procedures - Crash Pad - Body (Interior and Exterior) - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Main Crash Pad Assembly Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Body (Interior and Exterior) / Crash Pad / Main Crash Pad Assembly Repair procedures

Replacement
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Take care not to scratch the body surface.
•
Put on gloves to protect your hands.
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the console rear complete & console front complete assembly.
(Refer to Floor Console - "Floor Console Assembly")
3.
Remove the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
4.
Remove the cowl side trim.
(Refer to Interior Trim - "Cowl Side Trim")
5.
Remove the instrument cluster.
6.
Remove the steering column shroud panel.
(Refer to Crash Pad - "Steering Column Shroud Panel")
7.
Remove the AVN head unit.
8.
Remove the glove box housing.
(Refer to Crash Pad - "Glove Box Housing")
9.
Disconnect the steering column connectors.
10.
Down the steering column after loosening the mounting bolts.
11.
After loosening the mounting screws, then remove the crash pad garnish [RH] (A).

12.
Disconnect the connector (A).

13.
After loosening the mounting screws, then remove the crash pad main lower panel (A).

14.
After loosening the mounting screw, then remove the air duct assembly (A).

15.
Using a screwdriver or remover, remove the center speaker grille (A).

16.
After loosening the mounting screws, then remove the center speaker assembly (A).

17.
Disconnect the center speaker connectors (A).

18.
Disconnect the start/stop button connector (A).

19.
After loosening the mounting screws, then remove the cubis assembly (A).
20.
Disconnect the connector (B).

21.
After loosening the mounting screws, then remove the joint block (A).

22.
Disconnect the passenger's airbag connector (A).
23.
Loosen the mounting bolts.

24.
Using a screwdriver or remover, remove the photo sensor (A).
25.
Disconnect the photo sensor connector (B).

26.
Disconnect the passenger's airbag connectors (A).

27.
Disconnect the speaker [LH, RH] connectors (A).

28.
After loosening the mounting bolts and nuts, then remove the main crash pad assembly (A).

29.
Installation is the reverse of removal.
   
•
Make sure the crash pad fits onto the guide pins correctly.
•
Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
•
Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
•
Enter the anti- theft code for the radio, then enter the customer`s radio station presets.
Main Crash Pad Assembly Components and Components Location
Component Location 1. Main crash pad assembly ...

Cowl Cross Bar Assembly Components and Components Location
Component Location 1. Cowl cross bar assembly ...

See also:

INTERIOR LIGHT
CAUTION Do not use the interior lights for extended periods when the engine is not running. It may cause battery discharge. WARNING - Interior light Do not use the interior lights when driving in ...

Seats
Driver’s seat (1) Forward and rearward (2) Seatback angle (3) Seat cushion height (4) Lumbar support (5) Cushion extension (6) Driver position memory system (7) Seat warmer/ Seat warmer wit ...

Cooling system
Check cooling system components, such as radiator, coolant reservoir, hoses and connections for leakage and damage. Replace any damaged parts. ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com