Hyundai Equus Manuals

Hyundai Azera: Brake Pedal Repair procedures - Brake System - Brake System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Brake Pedal Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Brake System / Brake System / Brake Pedal Repair procedures

Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the crash pad lower panel.
3.
Remove the shower duct (A).

4.
Disconnect the stop lamp switch connector (A).

5.
Remove the brake pedal member mounting nut (B).

6.
Remove the snap pin (A) and clevis pin (B).

7.
Remove the brake pedal member assembly mounting nuts (A) and then remove the brake pedal assembly.

Inspection
1.
Check the bushing for wear.
2.
Check the brake pedal for bending or twisting.
3.
Check the brake pedal return spring for damage.
4.
Check the stop lamp switch.
(1)
Connect a circuit tester to the connector of stop lamp switch, and check whether or not there is continuity when the plunger of the stop lamp switch is pushed in and when it is released.
(2)
The stop lamp switch is in good condition if there is no continuity when plunger(A) is pushed.

Installation
1.
Pre-tighten the bracket fixing bolt (A) in dash panel.

2.
Install the brake booster and brake pedal member fixing nuts (A) securely.
Tightening torque:
12.7 ~ 15.7 N.m (1.3 ~ 1.6 kgf.m, 9.4 ~ 11.6 lb-ft)

3.
Tighten the bolt (A) securely in dash panel.
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)

4.
Install the snap pin (A) and clevis pin (B).

   
•
Before installing the pin, apply the grease to the clevis pin.
•
Use a new snap pin whenever installing.
5.
Install the stop lamp switch securely.
6.
Connect the stop lamp switch connector (A).

7.
Adjust the brake pedal height and free play.
8.
Check the brake pedal operation after installing the brake pedal.
9.
Install the shower duct (A).

10.
Install the crash pad lower panel.
11.
Reconnect the battery negative cable.
Adjustment
Stop lamp switch clearance adjustment
If the gap between stop lamp switch and bracket is not 1.0 ~ 2.0mm(0.04~ 0.08in), conform to below.
1.
Disconnect the stop lamp switch connector (A).

2.
Pull the locking plate (A) as indicated by the arrow.

3.
Turn stop lamp switch 45° counterclockwise and remove it.

4.
Fix the brake pedal arm and insert fully the stop lamp switch as hiding contact part.

5.
After inserting, turn the stop switch (A) 45° clockwise, and then assemble locking plate (B) by pushing.

6.
Confirm the gap between stop lamp switch and bracket.
Stop lamp clearance:
1.0 ~ 2.0 mm (0.04 ~ 0.08 in)

7.
Connect the stop lamp switch connector.
Brake Pedal Components and Components Location
Components 1. Cowl bracket2. Brake pedal member assembly3. Stop lamp switch4. Return spring5. Brake pedal stopper6. Clevis pin7. Snap pin8. Brake pedal ...

Front Disc Brake Components and Components Location
Components 1. Guide rod bolt2. Bleed screw3. Caliper carrier4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer ...

See also:

Mode Control Actuator Repair procedures
Inspection 1. Ignition "OFF” 2. Disconnect the connector of mode control actuator. 3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to the term ...

Glove box lamp
The glove box lamp comes on when the glove box is opened. The parking lights or headlights must be ON for the glove box lamp to function. CAUTION To prevent unnecessary charging system drain, c ...

Starting Mode
Press the key to display the Setup screen. You can select and control options related to [Display], [Sound], [Clock / Calendar], [Phone] and [System]. ✽ NOTICE Once settings have been c ...

Categories

Hyundai Azera Manuals

2011-2026 Copyright www.hgmanual.com