Hyundai Equus Manuals

Hyundai Azera: Engine And Transmission Assembly Repair procedures - Engine And Transmission Assembly - Engine Mechanical System - Hyundai Azera 2011-2025 Service ManualHyundai Azera: Engine And Transmission Assembly Repair procedures

Fifth generation HG (2011–2025) / Hyundai Azera 2011-2025 Service Manual / Engine Mechanical System / Engine And Transmission Assembly / Engine And Transmission Assembly Repair procedures

Removal
   
•
Use fender covers to avoid damaging painted surfaces.
•
To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
   
•
Mark all wiring and hoses to avoid misconnection.
1.
Release the residual pressure in fuel line.
2.
Remove the battery and battery tray.
3.
Remove the engine cover.
4.
Remove the air duct and air cleaner assembly.
(Refer to Intake And Exhaust System - "Air Cleaner")
5.
Remove the engine room under cover.
6.
Drain the engine coolant.
(Refer to Cooling System - "Coolant")
7.
Remove the radiator upper hose and lower hose.
(Refer to Cooling System - "Radiator Hose")
8.
Recover the refrigerant and then remove the high pressure pipe and low pressure pipe.
9.
Disconnect the (+) cable (A) from the junction box.
10.
Remove the ECM.
(1)
Disconnect the Engine contol module(ECM) connectors (B).
(2)
Disconnect the Injector drive box(IDB) connector (C).
(3)
Remove the ECM (D).

11.
Disconnect the front connector (B), and then remove the wiring protector (A).

12.
Remove the engine wirings from the engine room.
(1)
Disconnect the junction box connector (A).
(2)
Remove the ground bolt (B).
(3)
Remove the engine wirings from the engine room.

13.
Remove the transaxle wire harness connectors and control cable from the transaxle.
14.
Loosen the bolt & nut and then disconnect the lower arm (A) from the front knuckle.
Tightening Torque :
98.1~117.7N.m (10.0~12.0kgf.m, 72.3 ~ 86.6lb-ft)

15.
Remove the front stabilizer bar links (A).
Tightening Torque :
98.1~117.7N.m(10.0~12.0kgf.m, 72.3~86.8lb-ft)

16.
Disconnect the tie-rod end (A) from the front knuckle.
Tightening Torque :
34.3~44.1N.m(3.5~4.5kgf.m, 25.3~32.5lb-ft)

17.
Remove the drive shaft coking nut (A) from the front hub.
Tightening Torque :
240.3 ~ 269.7N.m(24.5 ~ 27.5kgf.m, 177.2 ~ 198.9lb-ft)

18.
Disconnect the driveshaft (A) from the front hub assembly.

19.
Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.
Tightening Torque:
32.4 ~ 37.3N.m(3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

20.
Disconnect the heater hoses.
(Refer to Cooling System - "Heater Hose")
21.
Disconnect the brake booster vacuum hose (A), the PSCV hose (B). Disconnect the and the fuel line (C).

22.
Remove the front muffler.
(Refer to Intake And Exhaust System - "Front Muffler")
23.
Remove the roll road bracket (A).
Tightening Torque:
107.9~117.7N.m (11.0~13.0kgf.m, 79.6~94.0lb-ft)
24.
Rremove the sub frame (B).
Tightening Torque
Sub frame mounting bolts & nuts :
156.9 ~ 176.5N.m (16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)
Sub frame bracket bolts & nuts :
44.1 ~ 58.8N.m (4.5 ~ 6.0kgf.m, 32.5 ~ 43.4lb-ft)

   
•
After removing the sub frame mounting bolt, the engine and transaxle assembly may fall downward, and so support them securely with floor jack.
•
Verify that the hoses and connectors are disconnected before removing the engine and transaxle assembly.
25.
Disconnect the ground cable, and then remove the engine mounting bracket.
(Refer to Engine And Transmission Assembly - "Engine Mounting")
26.
Disconnect the ground cable, and then remove the transaxle mounting bracket through bolt.
27.
Remove the engine and transaxle assembly by lifting vehicle.

   
When remove the engine and transaxle assembly, be careful not to damage any surrounding parts or body components.
Installation
Installation is in the reverse order of removal.
Perform the following :
•
Adjust a shift cable.
•
Refill engine with engine oil.
•
Refill a transaxle with fluid.
•
Refill a radiator and a reservoir tank with engine coolant.
•
Place a heater control knob on "HOT" position.
•
Clean battery posts and cable terminals and assemble.
•
Inspect for fuel leakage.
-
After assemble the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
-
Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.
•
Bleed air from the cooling system.
-
Start engine and let it run until it warms up. (until the radiator fan operates 3 or 4 times.)
-
Turn Off the engine and let it cool down. Check the level in the radiator, add coolant if needed. This will allow trapped air to be removed from the cooling system.
-
Put radiator cap on tightly, then run the engine again and check for leaks.
Engine Mounting Repair procedures
Removal and Installation [Engine mounting support bracket] 1. Install the jack to the edge of upper oil pan (A) to support the engine.     Insert the rubber block between jac ...

Engine Hanger Components and Components Location
Components Location ...

See also:

Adding equipment to or modifying your air bag-equipped vehicle
If you modify your vehicle by changing your vehicle's frame, bumper system, front end or side sheet metal or ride height, this may affect the operation of your vehicle's air bag system. ...

Changing the coolant
Have the coolant changed by an authorized HYUNDAI dealer according to the Maintenance Schedule at the beginning of this section. Put a thick cloth around the radiator cap before refilling the coolan ...

Smart key functions
1. Door lock 2. Door unlock 3. Trunk open 4. Alarm With a smart key, you can lock or unlock a door (and trunk) and even start the engine without inserting the key. Refer to the following, for mor ...

Categories

Hyundai Azera Manuals


© 2011-2025 Copyright www.hgmanual.com