Hyundai Azera: Rear Glass Defogger Printed Heater Repair procedures
Fifth generation HG (2011–2025) / Hyundai Azera 2011-2025 Service Manual / Body Electrical System / Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
Fifth generation HG (2011–2025) / Hyundai Azera 2011-2025 Service Manual / Body Electrical System / Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
| Inspection |
Wrap tin foil around the end of the voltmeter test lead to
prevent damaging the heater line. Apply finger pressure on the tin foil,
moving the tin foil along the grid line to check for open circuits. |
| 1. |
Turn on the defogger switch and use a voltmeter to measure
the voltage of each heater line at the glass center point. If a voltage
of approximately 6V is indicated by the voltmeter, the heater line of
the rear window is considered satisfactory.
|
| 2. |
If a heater line is burned out between the center point and (+) terminal, the voltmeter will indicate 12V.
|
| 3. |
If a heater line is burned out between the center point and (-) terminal, the voltmeter will indicate 0V.
|
| 4. |
To check for open circuits, slowly move the test lead in the
direction that the open circuit seems to exist. Try to find a point
where a voltage is generated or changes to 0V. The point where the
voltage has changed is the open-circuit point.
|
| 5. |
Use an ohmmeter to measure the resistance of each heater line
between a terminal and the center of a grid line, and between the same
terminal and the center of one adjacent heater line. The section with a
broken heater line will have a resistance twice as that in other
sections. In the affected section, move the test lead to a position
where the resistance sharply changes.
|
Repair Of Broken Heater Line
Prepare the following items:
| 1. |
Conductive paint. |
| 2. |
Paint thinner. |
| 3. |
Masking tape. |
| 4. |
Silicone remover. |
| 5. |
Using a thin brush:
Wipe the glass adjacent to the broken heater line, clean with
silicone remover and attach the masking tape as shown. Shake the
conductive paint container well, and apply three coats with a brush at
intervals of about 15 minutes apart. Remove the tape and allow
sufficient time for drying before applying power. For a better finish,
scrape away excess deposits with a knife after the paint has completely
dried. (Allow 24 hours).
|
Components and Components Location
Component Location
1. Rear glass defogger relay (Engine room relay box)2. Rear glass defogger switch (A/C controller)3. Rear glass defogger
...
Rear Glass Defogger Switch Repair procedures
Inspection
1.
The rear glass defogger switch inputs can be checked using the GDS.
2.
To check the input value of rear glass defogger switch, select option "IPM".
3.
To consult the present ...
See also:
Rail Pressure Sensor (RPS) Repair procedures
Inspection
1.
Connect the GDS on the Data Link Connector (DLC).
2.
Measure the output voltage of the RPS at idle and various engine speed.
ConditionOutput Voltage (V)Idle Approx. 1.21, ...
Troubleshooting
Troubleshooting
ProblemPossible causeSolutionNot pairingBluetooth device of Car is not discoverable modeEnter Bluetooth pairing (searching) modeUser’s phone is Bluetooth off modeUser’s phone set ...
Engine compartment
1. Engine oil dipstick
2. Engine oil filler cap
3. Engine coolant reservoir
4. Radiator cap
5. Brake fluid reservoir
6. Windshield washer fluid reservoir
7. Air cleaner
8. Positive battery te ...
Categories
Hyundai Azera Manuals
© 2011-2025 Copyright www.hgmanual.com