Hyundai Equus Manuals

Hyundai Azera: Side Airbag (SAB) Module Repair procedures - Airbag Module - Restraint - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Side Airbag (SAB) Module Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Restraint / Airbag Module / Side Airbag (SAB) Module Repair procedures

Removal
Front Side Airbag
1.
Disconnect the battery negative cable and wait for at least 3 minutes before beginning work.
2.
Remove the front seat assembly.
3.
Remove the seat back assembly.
   
The side airbag cannot be disassembled from the seat back assembly, so replace the seat back assembly when replacing the side airbag.
Rear Side Airbag
1.
Disconnect the battery negative cable and wait for at least 3 minutes before beginning work.
2.
Remove the rear seat cushion.
3.
Remove the rear seat back assembly.
   
The side airbag cannot be disassembled from the seat back assembly, so replace the seat back assembly when replacing the side airbag.
Installation
Front Side Airbag
   
Be sure to install the harness wires so they will not pinch or interfere with other parts.
   
•
Do not open the lid of the side airbag cover.
•
Make sure that the airbag assembly cover is installed properly. Improper installation may prevent the proper deployment.
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable and wait for at least three minutes.
3.
Install the new seat back assembly.
4.
Install the front seat assembly.
5.
Recline and slide the front seat forward fully, make sure the harness wires are not pinched of interfere with other parts.
6.
Reconnect the battery negative cable.
7.
After installing the side airbag (SAB), confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
Rear Side Airbag
   
Be sure to install the harness wires so they will not pinch or interfere with other parts.
   
•
Do not open the lid of the side airbag cover.
•
Make sure that the airbag assembly cover is installed properly. Improper installation may prevent the proper deployment.
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable and wait for at least three minutes.
3.
Install the new rear seat back assembly.
4.
Install the rear seat cushion.
5.
Reconnect the battery negative cable.
6.
After installing the side airbag (SAB), confirm proper system operation:
A.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
Side Airbag (SAB) Module Components and Components Location
Components ...

Curtain Airbag (CAB) Module Description and Operation
Description Curtain airbags are installed inside the headliner (LH and RH) and protect the driver and passenger from danger when side crash occurs. The SRSCM determines deployment of curtain ai ...

See also:

Trunk Trim Repair procedures
Replacement     • Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. • Take care not to bend or scratch the trim and ...

Starter Relay Repair procedures
Inspection 1. Remove the fuse box cover. 2. Remove the starter relay (A). 3. Using an ohmmeter, check that there is continuity between each terminal. TerminalContinuity30 - 87NO85 - 86Y ...

Vehicle stability management (VSM)
This system provides further enhancements to vehicle stability and steering responses when a vehicle is driven on a slippery road or a vehicle detects changes in coefficient of friction between righ ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com