Hyundai Equus Manuals

Hyundai Azera: Delivery Pipe Repair procedures - Fuel Delivery System - Engine Control/Fuel System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Delivery Pipe Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Engine Control/Fuel System / Fuel Delivery System / Delivery Pipe Repair procedures

Removal
   
In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do any repair work right after engine stops.
1.
Turn the ignition switch OFF and disconnect the battery negative (-) cable.
2.
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”)
   
When removing the fuel pump relay, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of “Release Residual Pressure in Fuel Line” work.
3.
Disconnect the injectors & rail pressure sensor connector (A).

4.
Remove the intake manifold.
5.
Remove the injector foam (A).

6.
Remove the high pressure fuel pipe.
(1)
Loosen the flange nut in the order of A,B with SST(09314-3V100).

(2)
Remove the high pressure pipe bracket bolt (A).

(3)
Remove the function block installation bolt (A).

7.
Remove the installation bolt (A), and then remove the delivery pipe and injector assembly from the engine.

Installation
   
•
Do not use already used injector fixing clip again.
   
•
Install the component with the specified torques.
•
Note that internal damage may occur when the component is dropped. In this case, use it after inspecting.
   
•
Apply engine oil to the injector O-ring.
•
Do not use already used injector O-ring again.
   
•
Do not use already used bolt again.
   
•
When insert the injector, be careful not to damage the injector tip.
1.
Installation is reverse of removal.
Delivery pipe installation bolt:
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
High pressure fuel pipe installation nut:
29.4 ~ 35.3 N.m (3.0 ~ 3.6 kgf.m, 21.7 ~ 26.0 lb-ft)
High pressure fuel pipe function block installation bolt:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
High pressure fuel pipe bracket installation bolt:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Accelerator Pedal Repair procedures
Removal 1. Turn the ignition switch OFF and disconnect the negative (-) battery cable. 2. Disconnect the accelerator position sensor connector (A). 3. Remove the installation nuts (B) and ...

High Pressure Fuel Pump Repair procedures
Removal     In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure f ...

See also:

Crankshaft Position Sensor (CKPS) Description and Operation
Description Crankshaft Position Sensor (CKPS) detects the crankshaft position and is one of the most important sensors of the engine control system. If there is no CKPS signal input, the engine ...

Auto Light Sensor Repair procedures
Inspection In the state of IGN1 ON, when multi function switch module detects auto light switch on, tail lamp relay output and head lamp low relay output are controlled according to auto light ...

Seat Belt Buckle Switch (BS) Repair procedures
Removal 1. Disconnect the battery negative cable, and wait for at least three minutes before beginning work. 2. Remove the front seat assembly. (Refer to Body - "Front seat") 3. Loosen th ...

Categories

Hyundai Azera Manuals

2011-2026 Copyright www.hgmanual.com