Hyundai Equus Manuals

Hyundai Azera: Rear Lower Arm Repair procedures - Rear Suspension System - Suspension System - Hyundai Azera 2011-2026 Service ManualHyundai Azera: Rear Lower Arm Repair procedures

Fifth generation HG (2011–2026) / Hyundai Azera 2011-2026 Service Manual / Suspension System / Rear Suspension System / Rear Lower Arm Repair procedures

Removal
1.
Remove the rear wheel & tire (A).
Tightening torque:
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

   
•
Be careful not to damage to the hub bolts when removing the front wheel & tire.
2.
Set up the transmission jack (A) under the lower arm (B).

3.
Loosen the nut and then remove the rear stabilizer link (A) from the lower arm and subframe.
Tightening torque:
98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

4.
Loosen the bolt & nut and then remove the rear lower arm (A) with the rear axle.
Tightening torque:
137.3~156.9N.m(14.0~16.0Kgf.m, 101.3~115.7lb-ft)
   
•
When removing the bolt, remove the upper arm in no-load condition by using the transmission jack.

5.
Loosen the bolt & nut and then remove the rear lower arm (A) from the sub frame.
Tightening torque:
107.9~117.7N.m(11.0~12.0Kgf.m, 79.6~86.8lb-ft)
   
•
When removing the bolt, remove the lower arm in no-load condition by using the transmission jack.

Installation
1.
Installation is the reverse of removal.
   
•
If you don't install the jack, the bolt may cut due to the high work load of lower arm mounting bolt.
•
Install the component with the specified torques.
•
When installing the bolt, install the lower arm in no-load condition by using the transmission jack.
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the rear lower arm for deformation.
3.
Check for all bolts and nut.
4.
Check the cracks or the cutting of the lower arm.
Rear Upper Arm Repair procedures
Removal 1. Remove the rear wheel & tire (A). Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     Be careful not to damage to the hub bolts when ...

Rear Stabilizer Bar Repair procedures
Replacement 1. Remove the rear wheel & tire (A). Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     • Be careful not to damage to the hub ...

See also:

Defroster
CAUTION - Conductors To prevent damage to the conductors bonded to the inside surface of the rear window, never use sharp instruments or window cleaners containing abrasives to clean the window. & ...

Driver Airbag (DAB) Module and Clock Spring Repair procedures
Removal 1. Disconnect the battery negative cable and wait for at least three minutes before beginning work. 2. Remove the driver airbag module mounting bolts (A). 3. Remove the wiring fix ...

Jump starting
Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow the jump starting procedures. If in doubt, we strongly recommend ...

Categories

Hyundai Azera Manuals

© 2011-2026 Copyright www.hgmanual.com